Lanner-electronic FW-7650 Manuale Utente

FW-7650 Series 19” 1U Intel Pentium4 / Celeron Rackmount Network Security Platform User’s Manual

4 1.4 MB-X71 System Board MB-X71 is the system board bundled with the FW-7650 Network security platform. The succeeding sections list all MB-X71 rel

51.4.2 Jumper Settings and I/O Connector The onboard jumper settings and I/O connector of MB-X71 are custom-tailored to fit the FW-7650 functionali

61.4.3 Connector Pin Assignments SFC1:Master/Slave Select Compact Flash Card ATA Disk Chip SCF1 Master Slave 1-2 Slave Master 2-3(Default CMOS1:C

7 LANA3~6 :Type 1 ( RJ-45) Pin No. Description 1 TX+ 2 TX- 3 RX+ 4 T45 5 T45 6 RX- 7 T78 8 T78 COMA1: RS-232 Serial Port #1 Connector ( D-

8 PSA1:20 Pin ATX Power Connector Pin No. Description Pin No. Description 1 +3.3V 11 +3.3V 2 +3.3V 12 -12V 3 GND 13 GND 4 +5V 14 SWITC

9VGAB1 : External VGA Connector ( 12 Pin Header ) Pin No. Description Pin No. Description 1 R 2 Ground 3 G 4 Ground 5 B 6 Ground 7 H-SYN

10PLRS1:Power LED,HD LED,Reset,Speaker Connector(11 Pin 2.54mm ) Pin No. Description 1 Power LED + 2 Power LED + 3 GND 4 HDD LED + 5 HDD LED - 6

11CF1:Compact Flash Connector Pin No. Description Pin No. Description 1 GND 26 CD1- 2 DATA3 27 DATA11 3 DATA4 28 DATA12 4 DATA5 29 DAT

12LEDE1：2x22 Pin Pin No. Description Pin No. Description 1 POWER LED 2 POWER LED 3 POWER LED STATUS 4 POWER LED STATUS 5 Lan1 Link/Active LE

13IDEB1 : IDE Interface Connector ( 40Pin 2.54mm Pitch Header) Pin No. Description Pin No. Description 1 Reset # 2 Ground 3 Data 7 4 Data 8

ii Copyright and Disclaimers © Copyright 2004 - Lanner Electronics Inc. All Rights Reserved The contents in this publication have been thoroughly ch

14PCIB1:124 Pin Mini PCI Socket Pin No. Description Pin No. Description 1 TIP 2 RING 3 8PMJ-3 4 8PMJ-1 5 8PMJ-6 6 8PMJ-2 7 8PMJ-7 8 8PMJ-

15PCIB1:124 Pin Mini PCI Socket(Continued last page) Pin No. Description Pin No. Description 61 IRDY 62 GROUND 63 +3.3V 64 FRAME 65 CLKRUN 6

161.5 FW-7650 19” 1U Rackmount Firewall Mechanisms This section of the manual describes the mechanical and device nomenclature of FW-7650. 1.5.1 F

171.5.3 Rear View Figure 6 – FW-7650 Rear View  Power Switch: Click the Power Switch , and the system will be power on. Faulty or improper u

C h a p t e r 2 FW-7650 Hardware Installation Guide 2.1 Hardware Installation Guide Inside of FW-7650 - CPU Installation Step 1: Lo

Step 3: When inserting the CPU please note the correct orientation as shown. The notched corner should point toward the end of the lever Step 4:

Step 3: Press the latches into the notches of the RAM module. How to Remove the Hard Disk Bay Step 1: Open both latches of mobile rack by press i

Step 5: Put the cover back. Step 6: Screw the cover. - Installing Compact Flash Card Step 1: Insert the compact flash card into the slot ca

Chapter 3 Award BIOS Setup 3.1 BIOS Setup Award‘s ROM BIOS provides a built-in Setup program that allows users to modify the basic system configu

<Esc> Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu - Exit current page and return to Mai

iii Safety Instructions The following information relates to the safety of installation and maintenance personnel. Read all instructions before atte

Listed below are explanation of the keys displayed at the bottom of the screen: <ESC> : Exit the utility. <Ç È Æ Å> : Use arrow keys Ç

 Set Supervisor Password: Use this menu to set Supervisor Passwords  Set User Password: Use this menu to set User Passwords.  Save & Exit

Item Options Description Date Month DD YYYY Set the system date. Note that the ‘Day’ automatically changes when you set the date Time HH : MM :

IDE Channel 0 Master None Auto Manual Selecting ‘manual’ lets you set the remaining fields on this screen. Selects the type of fixed disk. "Use

Virus Warning: The default setting of Virus Warning is “Disabled”. When it is enabled, any attempt to write the boot sector and partition

PS/2 Mouse Function Control : When this option is set Enabled, AMIBIOS supports a PS/2 type mouse. The settings are Enabled or Disabled. The defa

3.5 Chipset Features Setup DRAM Clock : The chipset support synchronous and asynchronous mode between the host clock and DIMM clock. Host C

between the CAS and RAS strobe signals, used when DRAM is written to, read from, or refreshed. Fast gives faster performance. This field applies onl

3.6 Integrated Peripherals On-Chip (Primary/Secondary) PCI IDE : The Intel 82C440BX chipset contains a PCI IDE interface with support for

USB Keyboard Support : Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard. Init Display Fir

iv Getting Technical Assistance Should you encounter questions or problems with your FW-7650, Lanner Electronics is ready to assist you within the g

3.7 Power Management Setup The Power Management Setup allows you to configure you system to most effectively save energy while operating in a mann

There are four selections for Power Management, three of which have fixed mode setting Disable (Default) No power management. Disables all four mo

3.8 PnP/PCI Configuration This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows

The settings are : “Enabled and Disabled”. Resource Controlled By : The Award Plug and Play BIOS has the capacity to automatically configure all of

ISA/EISA and PCI/PnP. DMA Resources : The sub menu can let you control the DMA resource. DMA Resources : The sub menu can let you control the DMA

C0000,C4000,C8000,CC000,D0000,D4000,D8000,or DC000. PCI/VGA Palette Snoop : Leave this field at “Disabled”. The settings are “Enabled”, “Disabled”

3.9 PC Health Status CPU Temperature, Fan1 Speed, Fan2 Speed , Fan2 Speed, VCORE, +2.5, +3.3V, +5V, +12V : These items display the current

3.10 Load Optimized Defaults When you press “Enter” on this item, you get a confirmation dialog box with a message similar to: Load Optimized Defa

3.13 Exit Without Saving Pressing <Enter> on this item asks for confirmation: Quit without saving (Y/N)? Y This allows you to exit Setup with

Appendix A Power Supply Power Supply Specification AC Input Spec : VOLTAGE 100 - 240 VAC FULL RANGE (±10% tolerance) Output Specifications Output

v Table of Contents Copyright and Disclaimers...ii

Appendix B Watchdog Timer Introduction Most systems need to be self-reliant. It's not usually possible to wait for someone to reboot them if t

the WDT status register will set . Watch Dog Timer Control Register (Index =71h, Default=00h) Bit Description 7 WDT is reset upon a CIR interrupt

A p p e n d i x C Console Redirection Console redirection allows you to maintain a system from a remote location by re-directing keyboard input and

A p p e n d i x D LCD Module and Key Pad For FW-7650 Purpose The purpose of this document is to provide installation information for the LCD module

=>Direct write the function to your program. 2.Read_KeyPad(); =>This Function get the KeyPad number if user pressed key. =>Direct write fu

Terms and Conditions Date:2004.07.08 Warranty Policy 1. All products are warranted against defects in materials and workmanship for a period of t

RMA Service Request Form When requesting RMA service, please fill out this RMA Service Request Form. Without this form your RMA will be REJECTED!!!

PEXNSD01-040709 Version 1.0 Printed and published in Taiwan

vi 3.4 BIOS Features Setup ... 27 3.5 Chipset Features Setup...

1C h a p t e r 1 Getting Started 1.1 Introduction Figure 1 – FW-7650 Outlook The FW-7650 is a 1U rackmount network security solution targeting the

21.2 Technical Specifications Model Name FW-7650 SBC SBC MB-X71 CPU Socket 478 for Intel® Pentium™ 4/Celeron Processor, up to 2.4GHz,533MHZ FSB Chi

31.3 Packing Contents Carefully unpack your package and make sure that you have the following items.  FW-7650 Network security Platform  Console